Odys Fusion gerootet; CWM? CM? jmd schon soweit?

[violentstorm]

Hi,

nach einen kurzen Exkurs mit dem Odys Xelio, habe ich mir nun das Fusion geholt.

Es ließ sich erfolgreich mitRoot Many Android rooten.

Hat schon jemand ein CWM und CM installiert? oder eine andere Custom Firmware?

Bis jetzt habe ich heraus bekommen, dass die Plattform folgende ist:

rockchip rk30sdk

leider habe ich noch keine passende Firmware gefunden.


Ach und dann hab ich noch das Problem, dass trotz Reset das Gerät nicht in den Deepsleep geht; ist das bei euch genau so, oder habe ich da noch was verfriemelt?

 

[netlars]

Für Rockchip basierte Geräte bieten wir hier Firmwares an. Unter anderem ist auch eine Beta von CM10.1 vorhanden! In den kommenden Tagen werden wir auch noch eine bereitstellen, wo wir Bugs beseitigt haben.

Alles auf eigenes Risiko

netlars

 

[violentstorm]

Oh sehr cool, da werd ich gleich mal vorbei schauen

 

[violentstorm]

Update:

habe die Genio Firmware installiert bekommen, musste dafür noch den CWM ersetzen und /cache formatieren, damit es funktioniert.

Leider scheint das Genio Tablet einen anderen Touchscreen-Treiber zu haben als das Fusion, denn Touch funktioniert leider nicht mehr...

 

[netlars]

Den Kernel in dem Paket hast du aber schon gegen deinen original Kernel ersetzt?

 

[violentstorm]

Oehm.... Das ist dann wohl etwas an mir vorbei gegangen... Ich hab gedacht, dass der Kernel funktioniert, da die HW ja die selbe ist, nur dass das Fusion etwas niedriger getaktet ist...

 

[netlars]

Nein, der Kernel muss immer passend zum Tablet gewählt werden, da er ja letztendlich die ganze Hardware konfiguriert. Und es gibt immer irgendwelche Unterschiede zwischen den Tabs.

 

[violentstorm]

Ok;
Habe nun eine org Kernel erhalten und ausgetauscht; damit funktioniert auch der Touchscreen wieder :-D
Leider lässt sich das Wlan nicht aktivieren..

 

[netlars]

Vermutlich ist da wieder mal ein neuer Chip verbaut der wieder eine andere .ko benötigt.
Ich werde mir das mal anschauen.

Edit:

Ich brauche mal bitte ein dmesg.
Und öffne mal bitte ein Terminal, z.b. via ADB oder dem Terminal Emulator und poste mal bitte die Ausgabe von: "cat /sys/class/rkwifi/chip "

 

[pseudodeed]

Hi violentstorm,
kannst du mal ne Anleitung schreiben wie du und welche CWM ersetzt hast? Und wie man die CustomRom auf das Tablett bekommt? Bitte? Habe auch das Odys Fusion und würde auch gerne cm10 drauf haben. Danke LG
Oder
@netlars könnte ihr bitte eine Passende CFW für das ODYS Fusion bereitstellen? Warum ist das Odys Fusion nicht bei euch nicht mit Supportet? Ist ja baugleich wie das Odys Genio außer Wlan glaube ich und das der gleiche Prozessor 100 MHZ geringer getaktet ist.
Hier ist die Original Firmware des ODYS Fusion:
https://www.android-hilfe.de/forum/...s-fusion-stock-firmware-benoetigt.476280.html

LG

 

[violentstorm]

Ich habe den RK3066GENERIC_CWM von androtab.info runtergeladen und einfach das Recovery.img ersetzt und dann mit dem RKFlashtool nach Anleitung von crewrktablets geflasht. Musst nur, bevor du die Format NAND.zip installiert den Cache Formatieren im CWM. Der Rest ist straight forward.

@netlars:
cat /sys/class/rkwifi/chip gibt mir ein mt5931 zurück;
Dmesg werd ich dann noch machen, dazu muss ich das Tablet aber erstmal wieder rooten ;-)

 

[netlars]

Mmh, das ist komisch. der mt5931 sollte eigentlich funktionieren. Schau mal bitte unter /system/lib/modules ob die Datei dort vorhanden ist. Weiß jetzt nicht, ob wir den schon unter rk30 verbreitet haben oder erst unter rk30. Wenn der fehlt kann ich dir nen Patch machen.

@pseudodeed
wir machen keine CFW's speziel für ein Tablet. Wir bemühen uns, dass unsere Images unter allen Typen einer Baureihe laufen. d.h. alle rk29 haben ein eigenes Image (meist unter Loox vertrieben), alle rk30 (meist unter Genio) und rk31 (meist unter Chuwi V88).
Man muss immer den Kernel tauschen, gegen seinen vom Tablet. Da trotzdem Hardwareunteschiede bestehen, z.B. anderer Touch, anderes Display, anderes WLAN Modul usw. braucht jedes Tab seinen Kernel und wenn neue Tabs auftauchen, wie das Fusion z.b., dann kann auch mal sein, das eine spezielle ko fehlt. Dies versuchen wir dann im nächsten Image zu berücksichtigen, wenn es uns zugetragen wird, bzw. bieten einen Fix an um das Problem zu beheben. Leider sind auch wir machmal Machtlos, darum etwas nachsicht, Gedankenblitze dauern manchmal ein wenig.

netlars

Edit:
habe gerade selber nachgeschaut, es fehlt die ko, im rk30 Image, + noch eine andere Datei muss geändert werden.
Ich werde heute abend, spätestens morgen versuchen einen Fix zu erstellen.

 

[pseudodeed]

@ violentstorm
Super danke. Wo hast den Original Kernel her? kannst ihn mir auch geben?

@ netlars
A dann verstehe ich. Danke für diesen guten Support.

D. h. ich muss im Prinzip nur aus meiner Original Rom die Treiber und den Kernel ersetzen und dann kann ich Euer Custom Rom nehmen.
Das ist ja echt genial.
Dann noch ne kleine frage:
In welchem Ordner der Original FW befinden sich die Treiber und der Kernel?
UND/oder wo bekomme ich den Original Kernel des ODYS Fusion her?
Und sind die Treiber und Kernel aus der Original Rom (beim ODYS Fusion Android 4.1)
mit AOSP 4.2.2 20130501 kompatibel?

Diese Problems:
- some soft reboots while first boot-up
- Bluetooth

- some soft reboots while first boot-up Wenn ich das richtig verstehe läuft dann nach einigen reeboots die Rom richtig oder?
Was heißt Problem mit Bluetooth? Geht Bluetooth nicht? Kannst du das in dem nächsten Fix bitte beheben?

LG und Danke

 

[violentstorm]

Den org Kernel findest du in der Firmware, die du auch verlinkt hast ;-)

 

[pseudodeed]

A gefunden werde mal schauen ob ich heute abend Zeit habe die Rom zu Testen. Hast du schon getestet? Hast das mit dem Wlan hinbekommen? Wenn ja wie?

 

[netlars]

Diese Problems:
- some soft reboots while first boot-up
- Bluetooth

- some soft reboots while first boot-up Wenn ich das richtig verstehe läuft dann nach einigen reeboots die Rom richtig oder?
Was heißt Problem mit Bluetooth? Geht Bluetooth nicht? Kannst du das in dem nächsten Fix bitte beheben?

An diesen Problemen arbeiten wir gerade. Bluetooth ist etwas tricki und wird noch bissle Zeit benötigen.
Es gibt immer neue Informationen auf Crew RKTablets | Per aspera ad astra, we rock the Tablets.

Hier mal ein Wifi Fix, hoffe das das Modul geladen wird. http://crewrktablets.arctablet.com/?wpfb_dl=954
Bitte Rückantwort geben!

netlars

 

[pseudodeed]

Super Danke

@netlars
Wenn man von euch die 20130925151726_0xpAeB4b_ODYS Fusion - Firmware 20130627.zip intsalliert ist da dann ein Customrecovery dabei?
Wenn nicht kann ich einfach die recovery.img gegen eine andere ersetzen? z.B. gegen die RK3066GENERIC_CWM von androtab.info? Und wie kommt man bei dem Gerät in die Recovery rein?
Vielleicht weiß ja violentstorm wie man in die recovery rein kommt?

Würde gerne euere Firmware testen aber ungern ohne Recovery.

 

[netlars]

Bei unseren Custom Firmwares ist immer eine CWM Recovery bei.
Bei dem original Image natürlich nicht. Einfach die bei dem Original Image ersetzen.

Wie man da rein kommt beim Fusion weiß ich nicht. Eventl. Menu + Einschaltknopf gedrückt halten, so ist es zumindest bei meinem Tablet.

netlars

 

[pseudodeed]

Super danke teste ich dann. Wo gibt es eine zip Datei von den ROMS weil irgndwie sind alle .img und ich weis nicht wie man die über recovery flasht

Der ursprüngliche Beitrag von 13:24 Uhr wurde um 13:48 Uhr ergänzt:

Hallo violentstorm
habe ein Problem mit CWM weil der bringt immer überall Mount error. Habe versucht das Original ROM mit CWM zu flashen und das ging nicht. Bin nun die ganze zeit im CWM und kann nicht raus. Ne IDee? Wie mache ich jetzt weiter?

Der ursprüngliche Beitrag von 13:48 Uhr wurde um 14:01 Uhr ergänzt:

Hallo netlars oder violentstorm
Hilfe bitte die neuinstallation mit 20130925151726_0xpAeB4b_ODYS Fusion - Firmware 20130627.zip läuft ohne Fehler durch aber das Tablett startet nicht.
Bzw es kommt ein Roboter mit !

Oder anders gesagt wie kann ich meine Originale Firmware wieder herstellen? Wie gesagt bin nach der Anleitung ODYS Fusion - Update Anleitung.pdf vorgegangen und leider habe ich das Bild Roboter mit !. Habe das oben gennate packet benutzt. In der Log war leider auch keine Fehlermeldung.
Hilfe!?! Bitte?!?

Der ursprüngliche Beitrag von 14:01 Uhr wurde um 15:04 Uhr ergänzt:

Spoiler: Log

14:46:39 957 Loader Device Path(\\?\USB#VID_2207&PID_300A#5&9703451&0&3#{a5dcbf10-6530-11d2-901f-00c04fb951ed}),ThreadID=9292
14:46:39 962 INFO:Start to run
14:46:39 967 INFO:Start to test device
14:46:39 973 INFO:Test device OK
14:46:39 979 INFO:Start to download IDB
14:46:39 985 Flash Chip Information:
14:46:39 990 NO SIZE(MB) Manufacturer
14:46:39 995 ----------------------------------------------
14:46:40 000 0 8192MB MICRON
14:46:40 025 ----------------------------------------------
14:46:40 030 INFO:BuildFlashStateMap start
14:46:40 035 INFO: FindAllIDB start
14:46:40 044 INFO:UpdateIDBData start
14:46:40 073 INFO:Serial Number(0):
14:46:40 078 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
14:46:40 082 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00
14:46:40 431 INFO:UID(0):
14:46:40 436 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
14:46:40 441 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00
14:46:40 444 INFO:BlueTooth(0):
14:46:40 449 00000000: 00 00 00 00 00 00
14:46:40 454 INFO:Mac(0):
14:46:40 458 00000000: 00 00 00 00 00 00
14:46:40 463 INFO:WriteXIDBlock start
14:46:40 468 INFO:MakeEccSpareData start
14:46:40 479 INFO:WriteXIDBlock start
14:46:40 485 INFO:Writeing the 1th ID Block£¬Pos£º00000000(SEC)
14:46:40 489 INFO:Writing sector 00000000 ~ 00000015 ...
14:46:40 499 INFO:Reading sector 00000000 ~ 00000015 ...
14:46:40 506 INFO:check start
14:46:40 510 INFO:Writing sector 00000016 ~ 00000031 ...
14:46:40 520 INFO:Reading sector 00000016 ~ 00000031 ...
14:46:40 526 INFO:check start
14:46:40 531 INFO:Writing sector 00000032 ~ 00000047 ...
14:46:40 541 INFO:Reading sector 00000032 ~ 00000047 ...
14:46:40 547 INFO:check start
14:46:40 552 INFO:Writing sector 00000048 ~ 00000063 ...
14:46:40 562 INFO:Reading sector 00000048 ~ 00000063 ...
14:46:40 569 INFO:check start
14:46:40 573 INFO:Writing sector 00000064 ~ 00000079 ...
14:46:40 583 INFO:Reading sector 00000064 ~ 00000079 ...
14:46:40 590 INFO:check start
14:46:40 595 INFO:Writing sector 00000080 ~ 00000095 ...
14:46:40 605 INFO:Reading sector 00000080 ~ 00000095 ...
14:46:40 612 INFO:check start
14:46:40 617 INFO:Writing sector 00000096 ~ 00000111 ...
14:46:40 627 INFO:Reading sector 00000096 ~ 00000111 ...
14:46:40 634 INFO:check start
14:46:40 640 INFO:Writing sector 00000112 ~ 00000127 ...
14:46:40 650 INFO:Reading sector 00000112 ~ 00000127 ...
14:46:40 657 INFO:check start
14:46:40 661 INFO:Writing sector 00000128 ~ 00000143 ...
14:46:40 672 INFO:Reading sector 00000128 ~ 00000143 ...
14:46:40 678 INFO:check start
14:46:40 684 INFO:Writing sector 00000144 ~ 00000159 ...
14:46:40 694 INFO:Reading sector 00000144 ~ 00000159 ...
14:46:40 701 INFO:check start
14:46:40 706 INFO:Writing sector 00000160 ~ 00000175 ...
14:46:40 717 INFO:Reading sector 00000160 ~ 00000175 ...
14:46:40 723 INFO:check start
14:46:40 729 INFO:Writing sector 00000176 ~ 00000191 ...
14:46:40 740 INFO:Reading sector 00000176 ~ 00000191 ...
14:46:40 748 INFO:check start
14:46:40 755 INFO:Writing sector 00000192 ~ 00000207 ...
14:46:40 766 INFO:Reading sector 00000192 ~ 00000207 ...
14:46:40 768 INFO:check start
14:46:40 769 INFO:Writing sector 00000208 ~ 00000223 ...
14:46:40 775 INFO:Reading sector 00000208 ~ 00000223 ...
14:46:40 778 INFO:check start
14:46:40 779 INFO:Writing sector 00000224 ~ 00000239 ...
14:46:40 784 INFO:Reading sector 00000224 ~ 00000239 ...
14:46:40 787 INFO:check start
14:46:40 789 INFO:Writeing the 2th ID Block£¬Pos£º00004096(SEC)
14:46:40 789 INFO:Writing sector 00004096 ~ 00004111 ...
14:46:40 795 INFO:Reading sector 00004096 ~ 00004111 ...
14:46:40 797 INFO:check start
14:46:40 798 INFO:Writing sector 00004112 ~ 00004127 ...
14:46:40 803 INFO:Reading sector 00004112 ~ 00004127 ...
14:46:40 805 INFO:check start
14:46:40 806 INFO:Writing sector 00004128 ~ 00004143 ...
14:46:40 811 INFO:Reading sector 00004128 ~ 00004143 ...
14:46:40 813 INFO:check start
14:46:40 814 INFO:Writing sector 00004144 ~ 00004159 ...
14:46:40 819 INFO:Reading sector 00004144 ~ 00004159 ...
14:46:40 821 INFO:check start
14:46:40 822 INFO:Writing sector 00004160 ~ 00004175 ...
14:46:40 827 INFO:Reading sector 00004160 ~ 00004175 ...
14:46:40 829 INFO:check start
14:46:40 830 INFO:Writing sector 00004176 ~ 00004191 ...
14:46:40 835 INFO:Reading sector 00004176 ~ 00004191 ...
14:46:40 837 INFO:check start
14:46:40 838 INFO:Writing sector 00004192 ~ 00004207 ...
14:46:40 843 INFO:Reading sector 00004192 ~ 00004207 ...
14:46:40 845 INFO:check start
14:46:40 846 INFO:Writing sector 00004208 ~ 00004223 ...
14:46:40 852 INFO:Reading sector 00004208 ~ 00004223 ...
14:46:40 854 INFO:check start
14:46:40 854 INFO:Writing sector 00004224 ~ 00004239 ...
14:46:40 860 INFO:Reading sector 00004224 ~ 00004239 ...
14:46:40 862 INFO:check start
14:46:40 862 INFO:Writing sector 00004240 ~ 00004255 ...
14:46:40 868 INFO:Reading sector 00004240 ~ 00004255 ...
14:46:40 870 INFO:check start
14:46:40 871 INFO:Writing sector 00004256 ~ 00004271 ...
14:46:40 876 INFO:Reading sector 00004256 ~ 00004271 ...
14:46:40 878 INFO:check start
14:46:40 879 INFO:Writing sector 00004272 ~ 00004287 ...
14:46:40 884 INFO:Reading sector 00004272 ~ 00004287 ...
14:46:40 886 INFO:check start
14:46:40 887 INFO:Writing sector 00004288 ~ 00004303 ...
14:46:40 893 INFO:Reading sector 00004288 ~ 00004303 ...
14:46:40 895 INFO:check start
14:46:40 895 INFO:Writing sector 00004304 ~ 00004319 ...
14:46:40 901 INFO:Reading sector 00004304 ~ 00004319 ...
14:46:40 903 INFO:check start
14:46:40 904 INFO:Writing sector 00004320 ~ 00004335 ...
14:46:40 909 INFO:Reading sector 00004320 ~ 00004335 ...
14:46:40 911 INFO:check start
14:46:40 913 INFO:Writeing the 3th ID Block£¬Pos£º00008192(SEC)
14:46:40 914 INFO:Writing sector 00008192 ~ 00008207 ...
14:46:40 920 INFO:Reading sector 00008192 ~ 00008207 ...
14:46:40 922 INFO:check start
14:46:40 923 INFO:Writing sector 00008208 ~ 00008223 ...
14:46:40 928 INFO:Reading sector 00008208 ~ 00008223 ...
14:46:40 931 INFO:check start
14:46:40 932 INFO:Writing sector 00008224 ~ 00008239 ...
14:46:40 938 INFO:Reading sector 00008224 ~ 00008239 ...
14:46:40 940 INFO:check start
14:46:40 941 INFO:Writing sector 00008240 ~ 00008255 ...
14:46:40 946 INFO:Reading sector 00008240 ~ 00008255 ...
14:46:40 949 INFO:check start
14:46:40 949 INFO:Writing sector 00008256 ~ 00008271 ...
14:46:40 955 INFO:Reading sector 00008256 ~ 00008271 ...
14:46:40 957 INFO:check start
14:46:40 957 INFO:Writing sector 00008272 ~ 00008287 ...
14:46:40 963 INFO:Reading sector 00008272 ~ 00008287 ...
14:46:40 965 INFO:check start
14:46:40 966 INFO:Writing sector 00008288 ~ 00008303 ...
14:46:40 971 INFO:Reading sector 00008288 ~ 00008303 ...
14:46:40 974 INFO:check start
14:46:40 975 INFO:Writing sector 00008304 ~ 00008319 ...
14:46:40 982 INFO:Reading sector 00008304 ~ 00008319 ...
14:46:40 985 INFO:check start
14:46:40 987 INFO:Writing sector 00008320 ~ 00008335 ...
14:46:40 995 INFO:Reading sector 00008320 ~ 00008335 ...
14:46:40 999 INFO:check start
14:46:41 000 INFO:Writing sector 00008336 ~ 00008351 ...
14:46:41 006 INFO:Reading sector 00008336 ~ 00008351 ...
14:46:41 008 INFO:check start
14:46:41 009 INFO:Writing sector 00008352 ~ 00008367 ...
14:46:41 015 INFO:Reading sector 00008352 ~ 00008367 ...
14:46:41 017 INFO:check start
14:46:41 018 INFO:Writing sector 00008368 ~ 00008383 ...
14:46:41 023 INFO:Reading sector 00008368 ~ 00008383 ...
14:46:41 026 INFO:check start
14:46:41 027 INFO:Writing sector 00008384 ~ 00008399 ...
14:46:41 032 INFO:Reading sector 00008384 ~ 00008399 ...
14:46:41 035 INFO:check start
14:46:41 035 INFO:Writing sector 00008400 ~ 00008415 ...
14:46:41 041 INFO:Reading sector 00008400 ~ 00008415 ...
14:46:41 044 INFO:check start
14:46:41 045 INFO:Writing sector 00008416 ~ 00008431 ...
14:46:41 050 INFO:Reading sector 00008416 ~ 00008431 ...
14:46:41 052 INFO:check start
14:46:41 054 INFO:Writeing the 4th ID Block£¬Pos£º00012288(SEC)
14:46:41 055 INFO:Writing sector 00012288 ~ 00012303 ...
14:46:41 061 INFO:Reading sector 00012288 ~ 00012303 ...
14:46:41 063 INFO:check start
14:46:41 064 INFO:Writing sector 00012304 ~ 00012319 ...
14:46:41 070 INFO:Reading sector 00012304 ~ 00012319 ...
14:46:41 073 INFO:check start
14:46:41 073 INFO:Writing sector 00012320 ~ 00012335 ...
14:46:41 079 INFO:Reading sector 00012320 ~ 00012335 ...
14:46:41 081 INFO:check start
14:46:41 082 INFO:Writing sector 00012336 ~ 00012351 ...
14:46:41 088 INFO:Reading sector 00012336 ~ 00012351 ...
14:46:41 091 INFO:check start
14:46:41 092 INFO:Writing sector 00012352 ~ 00012367 ...
14:46:41 098 INFO:Reading sector 00012352 ~ 00012367 ...
14:46:41 101 INFO:check start
14:46:41 103 INFO:Writing sector 00012368 ~ 00012383 ...
14:46:41 110 INFO:Reading sector 00012368 ~ 00012383 ...
14:46:41 113 INFO:check start
14:46:41 114 INFO:Writing sector 00012384 ~ 00012399 ...
14:46:41 120 INFO:Reading sector 00012384 ~ 00012399 ...
14:46:41 122 INFO:check start
14:46:41 124 INFO:Writing sector 00012400 ~ 00012415 ...
14:46:41 129 INFO:Reading sector 00012400 ~ 00012415 ...
14:46:41 131 INFO:check start
14:46:41 132 INFO:Writing sector 00012416 ~ 00012431 ...
14:46:41 138 INFO:Reading sector 00012416 ~ 00012431 ...
14:46:41 140 INFO:check start
14:46:41 141 INFO:Writing sector 00012432 ~ 00012447 ...
14:46:41 147 INFO:Reading sector 00012432 ~ 00012447 ...
14:46:41 149 INFO:check start
14:46:41 150 INFO:Writing sector 00012448 ~ 00012463 ...
14:46:41 155 INFO:Reading sector 00012448 ~ 00012463 ...
14:46:41 157 INFO:check start
14:46:41 158 INFO:Writing sector 00012464 ~ 00012479 ...
14:46:41 163 INFO:Reading sector 00012464 ~ 00012479 ...
14:46:41 166 INFO:check start
14:46:41 166 INFO:Writing sector 00012480 ~ 00012495 ...
14:46:41 172 INFO:Reading sector 00012480 ~ 00012495 ...
14:46:41 174 INFO:check start
14:46:41 174 INFO:Writing sector 00012496 ~ 00012511 ...
14:46:41 180 INFO:Reading sector 00012496 ~ 00012511 ...
14:46:41 182 INFO:check start
14:46:41 183 INFO:Writing sector 00012512 ~ 00012527 ...
14:46:41 188 INFO:Reading sector 00012512 ~ 00012527 ...
14:46:41 190 INFO:check start
14:46:41 192 INFO:Writeing the 5th ID Block£¬Pos£º00016384(SEC)
14:46:41 193 INFO:Writing sector 00016384 ~ 00016399 ...
14:46:41 199 INFO:Reading sector 00016384 ~ 00016399 ...
14:46:41 201 INFO:check start
14:46:41 202 INFO:Writing sector 00016400 ~ 00016415 ...
14:46:41 208 INFO:Reading sector 00016400 ~ 00016415 ...
14:46:41 211 INFO:check start
14:46:41 211 INFO:Writing sector 00016416 ~ 00016431 ...
14:46:41 217 INFO:Reading sector 00016416 ~ 00016431 ...
14:46:41 219 INFO:check start
14:46:41 220 INFO:Writing sector 00016432 ~ 00016447 ...
14:46:41 225 INFO:Reading sector 00016432 ~ 00016447 ...
14:46:41 228 INFO:check start
14:46:41 228 INFO:Writing sector 00016448 ~ 00016463 ...
14:46:41 234 INFO:Reading sector 00016448 ~ 00016463 ...
14:46:41 236 INFO:check start
14:46:41 236 INFO:Writing sector 00016464 ~ 00016479 ...
14:46:41 242 INFO:Reading sector 00016464 ~ 00016479 ...
14:46:41 244 INFO:check start
14:46:41 245 INFO:Writing sector 00016480 ~ 00016495 ...
14:46:41 250 INFO:Reading sector 00016480 ~ 00016495 ...
14:46:41 252 INFO:check start
14:46:41 253 INFO:Writing sector 00016496 ~ 00016511 ...
14:46:41 258 INFO:Reading sector 00016496 ~ 00016511 ...
14:46:41 261 INFO:check start
14:46:41 261 INFO:Writing sector 00016512 ~ 00016527 ...
14:46:41 267 INFO:Reading sector 00016512 ~ 00016527 ...
14:46:41 269 INFO:check start
14:46:41 270 INFO:Writing sector 00016528 ~ 00016543 ...
14:46:41 275 INFO:Reading sector 00016528 ~ 00016543 ...
14:46:41 278 INFO:check start
14:46:41 279 INFO:Writing sector 00016544 ~ 00016559 ...
14:46:41 285 INFO:Reading sector 00016544 ~ 00016559 ...
14:46:41 287 INFO:check start
14:46:41 288 INFO:Writing sector 00016560 ~ 00016575 ...
14:46:41 293 INFO:Reading sector 00016560 ~ 00016575 ...
14:46:41 296 INFO:check start
14:46:41 296 INFO:Writing sector 00016576 ~ 00016591 ...
14:46:41 302 INFO:Reading sector 00016576 ~ 00016591 ...
14:46:41 304 INFO:check start
14:46:41 305 INFO:Writing sector 00016592 ~ 00016607 ...
14:46:41 311 INFO:Reading sector 00016592 ~ 00016607 ...
14:46:41 313 INFO:check start
14:46:41 314 INFO:Writing sector 00016608 ~ 00016623 ...
14:46:41 320 INFO:Reading sector 00016608 ~ 00016623 ...
14:46:41 322 INFO:check start
14:46:41 322 INFO:start to erase system disk
14:46:41 323 INFOownload IDB OK
14:46:41 325 INFO:Start to reset device
14:46:41 327 INFO:Reset device OK
14:46:41 329 INFO:LoaderThread Finish
14:46:43 200 Image Thread Path(\\?\USB#VID_2207&PID_300A#5&9703451&0&3#{a5dcbf10-6530-11d2-901f-00c04fb951ed}),ThreadID=9012
14:46:43 202 INFO:Start to test device
14:46:56 233 INFO:Test device OK
14:46:56 236 INFO:Start to download file
14:46:56 241 INFO: Start to download files to flash,backup offset=0x18000
14:46:56 244 INFO:Flash Start to download file to flash
14:46:56 267 Info:RKA_File_Download start,file=misc,offset=0x2000
14:46:56 274 Info:RKA_File_Download start,file=kernel,offset=0x4000
14:46:57 694 Info:RKA_File_Download start,file=boot,offset=0x8000
14:46:59 399 Info:RKA_File_Download start,file=recovery,offset=0x10000
14:47:01 854 Info:RKA_File_Download start,file=system,offset=0x31a000
14:48:20 054 INFO: Download files to flash finished,Total(438681408)B
14:48:20 055 INFO: Start to check data
14:48:20 058 INFO:Start to check download data
14:48:20 087 Info:RKA_File_Check start,file=misc,offset=0x2000
14:48:20 099 Info:RKA_File_Check start,file=kernel,offset=0x4000
14:48:20 950 Info:RKA_File_Check start,file=boot,offset=0x8000
14:48:21 958 Info:RKA_File_Check start,file=recovery,offset=0x10000
14:48:23 417 Info:RKA_File_Check start,file=system,offset=0x31a000
14:49:09 534 INFOownload file OK,Elapsed(133287MS)
14:49:09 540 INFO:Run OK
14:50:23 649 Info:wait for exiting scan thread start
14:50:23 762 Info:wait for exiting main thread start
14:50:23 778 ProcessID:1284,ThreadID:10608,RefCount:0

 

[violentstorm]

@ pseudodeed:

ließ doch mal den Beitrag von mir weiter vorn.... dort habe ich geschrieben, dass du einen anderen CWM verwenden musst, damit du /cache (unter dem Menü mount & Storage)formatieren kannst, damit es anschließend funktioniert.

Genau diesen CWM musst du auch verwenden, wenn du die org. Firmware wieder zurück flashen möchtest und auch wieder /cache formatieren.


@netlars:

dein update lässt sich grad nicht installieren, wenn ich es im CWM installiere, dann bleibt das Tablet beim Bootscreen von Odys hängen... und wenn ich es in update.zip umbenenne lässt es sich auch nicht installieren..

Edit:

per adb push erhalte ich für das MT5931.ko ein "error device not found"
per insmod. failed (Exec format error)

Der ursprüngliche Beitrag von 15:55 Uhr wurde um 16:39 Uhr ergänzt:

hier mal noch mein dmesg:

<6>[    0.000000] Initializing cgroup subsys cpu
<5>[    0.000000] Linux version 3.0.8+ (yflan@Ubuntu3) (gcc version 4.4.3 (GCC) ) #308 SMP PREEMPT Tue Mar 26 10:13:21 CST 2013
<4>[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
<4>[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
<4>[    0.000000] Machine: RK30board
<6>[    0.000000] memory reserve: Memory(base:0x91800000 size:80M) reserved for <ion>
<6>[    0.000000] memory reserve: Memory(base:0x90c00000 size:12M) reserved for <fb0 buf>
<6>[    0.000000] memory reserve: Memory(base:0x90000000 size:12M) reserved for <fb2 buf>
<6>[    0.000000] memory reserve: Memory(base:0x8fa00000 size:6M) reserved for <camera_ipp_mem>
<6>[    0.000000] memory reserve: Total reserved 110M
<4>[    0.000000] Memory policy: ECC disabled, Data cache writeback
<6>[    0.000000] bootconsole [earlycon0] enabled
<4>[    0.000000] CPU SRAM: copied sram code from c0b22000 to fef00100 - fef022c0
<4>[    0.000000] CPU SRAM: copied sram data from c0b241c0 to fef03000 - fef0385c
<6>[    0.000000] L310 cache controller enabled
<6>[    0.000000] l2x0: 16 ways, CACHE_ID 0x4100c0c8, AUX_CTRL 0x76050001, Cache size: 524288 B
<4>[    0.000000] DDR DEBUG: version 1.00 20121016
<4>[    0.000000] DDR DEBUG: DDR3 Device
<4>[    0.000000] DDR DEBUG: 1 CS, ROW=15, Bank=8, COL=10, Total Capability=1024MB
<4>[    0.000000] DDR DEBUG: init success!!! freq=396MHz
<4>[    0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=180
<4>[    0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=180
<4>[    0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=180
<4>[    0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x5, DGSL=1 extra clock, DGPS=180
<4>[    0.000000] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
<4>[    0.000000] DDR DEBUG: DRV Pull-Up=0xb, DRV Pull-Dwn=0xb
<4>[    0.000000] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
<4>[    0.000000] rk30_iomux_init
<4>[    0.000000] Boot mode: 6 flag: 0xc3524200
<7>[    0.000000] On node 0 totalpages: 233984
<7>[    0.000000] free_area_init_node: node 0, pgdat c0b20ac0, node_mem_map c15aa000
<7>[    0.000000]   Normal zone: 1744 pages used for memmap
<7>[    0.000000]   Normal zone: 0 pages reserved
<7>[    0.000000]   Normal zone: 193328 pages, LIFO batch:31
<7>[    0.000000]   HighMem zone: 304 pages used for memmap
<7>[    0.000000]   HighMem zone: 38608 pages, LIFO batch:7
<6>[    0.000000] PERCPU: Embedded 7 pages/cpu @c1db2000 s7072 r8192 d13408 u32768
<7>[    0.000000] pcpu-alloc: s7072 r8192 d13408 u32768 alloc=8*4096
<7>[    0.000000] pcpu-alloc: [0] 0 [0] 1
<4>[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 231936
<5>[    0.000000] Kernel command line: console=ttyFIQ0 androidboot.console=ttyFIQ0 init=/init initrd=0x62000000,0x00130000 mtdparts=rk29xxnand:0x00002000@0x00002000(misc),0x00004000@0x00004000(kernel),0x00008000@0x00008000(boot),0x00008000@0x00010000(recovery),0x000C0000@0x00018000(backup),0x00040000@0x000D8000(cache),0x00500000@0x00118000(userdata),0x00002000@0x00618000(kpanic),0x00140000@0x0061A000(system),-@0x0075A000(user) bootver=2012-11-13#1.20 firmware_ver=4.1.1
<6>[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>[    0.000000] Memory: 762MB 152MB = 914MB total
<5>[    0.000000] Memory: 907552k/907552k available, 141024k reserved, 155648K highmem
<5>[    0.000000] Virtual kernel memory layout:
<5>[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
<5>[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
<5>[    0.000000]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
<5>[    0.000000]     vmalloc : 0xf7000000 - 0xfe800000   ( 120 MB)
<5>[    0.000000]     lowmem  : 0xc0000000 - 0xf6800000   ( 872 MB)
<5>[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
<5>[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
<5>[    0.000000]       .init : 0xc0408000 - 0xc04c5000   ( 756 kB)
<5>[    0.000000]       .text : 0xc04c5000 - 0xc0ab26a8   (6070 kB)
<5>[    0.000000]       .data : 0xc0ab4000 - 0xc0b215e0   ( 438 kB)
<5>[    0.000000]        .bss : 0xc0b25024 - 0xc15a95a8   (10770 kB)
<6>[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
<6>[    0.000000] Preemptible hierarchical RCU implementation.
<6>[    0.000000] NR_IRQS:416
<4>[    0.000000] rk30_gpio_init: 176 gpio irqs in 6 banks
<6>[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
<6>[    0.000000] Console: colour dummy device 80x30
<6>[    0.004957] Calibrating delay loop (skipped) preset value.. 1631.46 BogoMIPS (lpj=8157341)
<6>[    0.013877] pid_max: default: 32768 minimum: 301
<6>[    0.019107] Mount-cache hash table entries: 512
<6>[    0.024564] Initializing cgroup subsys debug
<6>[    0.029187] Initializing cgroup subsys cpuacct
<6>[    0.034096] Initializing cgroup subsys freezer
<6>[    0.038946] CPU: Testing write buffer coherency: ok
<4>[    0.144912] CPU1: Booted secondary processor
<6>[    0.144950] Brought up 2 CPUs
<6>[    0.152868] SMP: Total of 2 processors activated (3262.93 BogoMIPS).
<6>[    0.160023] devtmpfs: initialized
<6>[    0.171180] NET: Registered protocol family 16
<4>[    0.176129] last_log: 0xef500000 0xc0b29240
<6>[    0.283178] rk29sdk_wifi_bt_gpio_control_init: init finished
<6>[    0.293682] console [ttyFIQ0] enabled, bootconsole disabled
<6>[    0.299873] Registered FIQ tty driver ef48fc00
<6>[    0.312386] bio: create slab <bio-0> at 0
<4>[    0.316608] wm831x_dcdc_init
<4>[    0.316794] wm831x_ldo_init
<5>[    0.317162] SCSI subsystem initialized
<6>[    0.317350] usbcore: registered new interface driver usbfs
<6>[    0.317429] usbcore: registered new interface driver hub
<6>[    0.319638] usbcore: registered new device driver usb
<6>[    0.319955] rk30_i2c rk30_i2c.0: i2c-0: RK30 I2C adapter
<6>[    0.320188] rk30_i2c rk30_i2c.1: i2c-1: RK30 I2C adapter
<6>[    0.320353] rk30_i2c rk30_i2c.2: i2c-2: RK30 I2C adapter
<6>[    0.320462] rk30_i2c rk30_i2c.3: i2c-3: RK30 I2C adapter
<6>[    0.320571] rk30_i2c rk30_i2c.4: i2c-4: RK30 I2C adapter
<6>[    0.368525] rk30-adc rk30-adc: rk30 adc: driver initialized
<4>[    0.400181] rk30_adc_battery_load_capacity: open file /data/bat_last_capacity.dat failed
<6>[    0.400350] rk30_adc_battery: driver initialized
<4>[    0.400615] timed_gpio_probe
<6>[    0.400702] Advanced Linux Sound Architecture Driver Version 1.0.24.
<6>[    0.401099] Bluetooth: Core ver 2.16
<6>[    0.401148] NET: Registered protocol family 31
<6>[    0.401160] Bluetooth: HCI device and connection manager initialized
<6>[    0.401176] Bluetooth: HCI socket layer initialized
<6>[    0.401188] Bluetooth: L2CAP socket layer initialized
<6>[    0.401212] Bluetooth: SCO socket layer initialized
<6>[    0.401410] cfg80211: Calling CRDA to update world regulatory domain
<4>[    0.458151] rk fb probe ok!
<4>[    0.458246] wm831x_i2c_init
<3>[    0.458937] i2c i2c-1: No ack, Maybe slave(addr: 0x34) not exist or abnormal power-on, retry 2...
<3>[    0.459587] i2c i2c-1: No ack, Maybe slave(addr: 0x34) not exist or abnormal power-on, retry 1...
<3>[    0.460233] i2c i2c-1: No ack, Maybe slave(addr: 0x34) not exist or abnormal power-on, retry 0...
<3>[    0.460253] wm831x 1-0034: Failed to read parent ID: -11
<4>[    0.460274] wm831x: probe of 1-0034 failed with error -11
<4>[    0.498686] tps65910_pre_init,line=38
<6>[    0.502681] TPS65910 Set default voltage.
<4>[    0.505062] tps65910_pre_init,line=230
<4>[    0.550062] tps65910_post_init,line=238
<4>[    0.550075] tps65910_post_init:g_pmic_type=2
<4>[    0.565176] tps65910_post_init set vio vcc_io=3300000mV end
<4>[    0.566410] tps65910_post_init set vpll vdd11=2500000mV end
<4>[    0.567633] tps65910_post_init set vdig2 vdd11=1100000mV end
<4>[    0.568852] tps65910_post_init set vaux33 vcc_tp=3300000mV end
<4>[    0.571698] tps65910_post_init set vdd1 vdd_cpu=1200000mV end
<4>[    0.574543] tps65910_post_init set vdd2 vcc_ddr=1200000mV end
<4>[    0.575764] tps65910_post_init set vdig1 vcc18_cif=1800000mV end
<4>[    0.576983] tps65910_post_init set vaux1 vcc25_hdmi=2500000mV end
<4>[    0.578202] tps65910_post_init set vaux2 vcca33=3300000mV end
<4>[    0.579421] tps65910_post_init set vdac vccio_wl=1800000mV end
<4>[    0.580638] tps65910_post_init set vmmc vcc28_cif=2800000mV end
<4>[    0.580752] tps65910_post_init,line=330 END
<4>[    0.580764] tps65910_i2c_probe:irq=324,irq_base=352,gpio_base=364
<6>[    0.590908] tps65910-rtc tps65910-rtc: rtc core: registered tps65910 as rtc0
<4>[    0.594719] tps65910_rtc_probe:ok
<4>[    0.594766] start_charge_logo_display
<6>[    0.594795] Switching to clocksource timer1
<6>[    0.594949] Switched to NOHz mode on CPU #1
<4>[    0.595006] lcdc0:reg_phy_base = 0x1010c000,reg_vir_base:0xf701c000
<4>[    0.595037] fb0:win1
<4>[    0.595041] fb1:win0
<4>[    0.595044] fb2:win2
<4>[    0.600227] lcdc0: dclk:49875000>>fps:58 rk30_load_screen for lcdc0 ok!
<6>[    0.604398] Switched to NOHz mode on CPU #0
<4>[    0.622541] fb0:phy:90c00000>>vir:f8000000>>len:0xc00000
<4>[    0.622758] rk_fb_register>>>>>fb0
<4>[    0.622917] rk_fb_register>>>>>fb1
<4>[    0.623078] rk_fb_register>>>>>fb2
<4>[    0.623091] lcdc0 wakeup from stanby
<6>[    0.623100] lcdc0 win1 open
<4>[    0.648054] rk30 lcdc0 probe ok!
<4>[    0.648112] lcdc1:reg_phy_base = 0x1010e000,reg_vir_base:0xf7028000
<4>[    0.648146] fb0:win1
<4>[    0.648150] fb1:win0
<4>[    0.648153] fb2:win2
<4>[    0.648205] lcdc1: dclk:74250000>>fps:60 rk30_load_screen for lcdc1 ok!
<4>[    0.671439] fb3:phy:90000000>>vir:f9000000>>len:0xc00000
<4>[    0.671638] rk_fb_register>>>>>fb3
<4>[    0.671810] rk_fb_register>>>>>fb4
<4>[    0.671966] rk_fb_register>>>>>fb5
<4>[    0.671976] rk30 lcdc1 probe ok!
<4>[    0.672036] boot with tps65910 need  pwm_regultor
<4>[    0.672084] pwm_regulator_probe:n_voltages=17
<4>[    0.672229] pwm_regulator.0: driver initialized
<4>[    0.672240] rk30 pwm regulator is ok with pmu tps65910
<4>[    0.682285] pwm_regulator_probe set vdd_core=1100000mV end
<6>[    0.771800] NET: Registered protocol family 2
<6>[    0.771930] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[    0.772261] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>[    0.774096] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
<6>[    0.775178] TCP: Hash tables configured (established 131072 bind 65536)
<6>[    0.775192] TCP reno registered
<6>[    0.775208] UDP hash table entries: 512 (order: 2, 16384 bytes)
<6>[    0.775247] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
<6>[    0.775584] NET: Registered protocol family 1
<4>[    0.775775] RK29 Backlight Driver Initialized.
<6>[    0.775961] Unpacking initramfs...
<6>[    0.831459] Freeing initrd memory: 1216K
<6>[    0.831649] rk30-tsadc rk30-tsadc: initialized
<4>[    0.840357] charge_lowerpower_probe
<4>[    0.840382] charge_lowerpower: probe of charge_lowerpower failed with error -1062281876
<6>[    0.840601] Loaded driver for PL330 DMAC-1 rk29-pl330
<6>[    0.840617]       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
<6>[    0.840763] Loaded driver for PL330 DMAC-2 rk29-pl330
<6>[    0.840777]       DBUFF-64x8bytes Num_Chans-7 Num_Peri-20 Num_Events-14
<4>[    0.879913] highmem bounce pool size: 64 pages
<6>[    0.880066] ashmem: initialized
<6>[    0.888740] fuse init (API version 7.16)
<6>[    0.892109] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
<6>[    0.892123] io scheduler noop registered
<6>[    0.892131] io scheduler deadline registered
<6>[    0.892170] io scheduler cfq registered (default)
<6>[    0.897141] rga: Driver loaded succesfully
<4>[    0.921736] rk_serial.c v1.3 2012-12-14
<6>[    0.921945] rk_serial rk_serial.0: dma_rx_buffer 0xffdfc000
<6>[    0.921955] rk_serial rk_serial.0: dma_rx_phy 0x8f6de000
<6>[    0.921968] rk_serial rk_serial.0: serial_rk_init_dma_rx sucess
<6>[    0.921980] rk_serial.0: ttyS0 at MMIO 0x10124000 (irq = 66) is a rk29_serial.0
<6>[    0.974890] rk_serial rk_serial.0: membase 0xf704c000
<6>[    0.980200] rk_serial.3: ttyS3 at MMIO 0x20068000 (irq = 69) is a rk29_serial.3
<6>[    1.074919] rk_serial rk_serial.3: membase 0xf7050000
<6>[    1.080841] Rockchip ion module(version: 1.0) is successfully loaded
<6>[    1.095517] loop: module loaded
<6>[    1.099038] Android kernel panic handler initialized (bind=kpanic)
<6>[    1.107413] PPP generic driver version 2.4.2
<6>[    1.111916] PPP Deflate Compression module registered
<6>[    1.114952] PPP BSD Compression module registered
<6>[    1.115652] PPP MPPE Compression module registered
<6>[    1.115668] NET: Registered protocol family 24
<6>[    1.115811] usbcore: registered new interface driver asix
<6>[    1.115862] usbcore: registered new interface driver cdc_ether
<6>[    1.115908] usbcore: registered new interface driver dm9620
<6>[    1.115952] usbcore: registered new interface driver SR9700_android
<6>[    1.116058] usbcore: registered new interface driver net1080
<6>[    1.116107] usbcore: registered new interface driver cdc_subset
<6>[    1.116152] usbcore: registered new interface driver zaurus
<6>[    1.116175] cdc_ncm: 04-Aug-2011
<6>[    1.116217] usbcore: registered new interface driver cdc_ncm
<4>[    1.116229] Rockchip WiFi SYS interface (V1.00) ...
<6>[    1.116267] Initializing USB Mass Storage driver...
<6>[    1.116325] usbcore: registered new interface driver usb-storage
<6>[    1.116341] USB Mass Storage support registered.
<6>[    1.116526] usbcore: registered new interface driver usbserial
<6>[    1.116570] USB Serial support registered for generic
<6>[    1.116621] usbcore: registered new interface driver usbserial_generic
<6>[    1.116634] usbserial: USB Serial Driver core
<6>[    1.116672] USB Serial support registered for GSM modem (1-port)
<6>[    1.117125] usbcore: registered new interface driver option
<6>[    1.117140] option: v0.7.2:USB Driver for GSM modems
<6>[    1.327559] DWC_OTG: ^^^^^^^^^^^^^^^^^Device Mode
<6>[    1.327576] usb20_otg usb20_otg: DWC OTG Controller
<6>[    1.327594] usb20_otg usb20_otg: new USB bus registered, assigned bus number 1
<6>[    1.327617] usb20_otg usb20_otg: irq 48, io mem 0x00000000
<6>[    1.327624] DWC_OTG: dwc_otg_hcd_start controller in device mode,everest
<6>[    1.327661] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[    1.327670] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[    1.327679] usb usb1: Product: DWC OTG Controller
<6>[    1.327685] usb usb1: Manufacturer: Linux 3.0.8+ dwc_otg_hcd
<6>[    1.327692] usb usb1: SerialNumber: usb20_otg
<6>[    1.327926] hub 1-0:1.0: USB hub found
<6>[    1.327940] hub 1-0:1.0: 1 port detected
<6>[    1.328436] DWC_OTG: host20_driver_probe host2.0 reg addr: 0x101c0000 remap:0xf7100000
<4>[    1.394897] rk30_adc_battery_load_capacity: open file /data/bat_last_capacity.dat failed
<6>[    1.538771] DWC_OTG: ^^^^^^^^^^^^^^^^^^Host Mode
<6>[    1.538784] usb20_host usb20_host: DWC OTG Controller
<6>[    1.538803] usb20_host usb20_host: new USB bus registered, assigned bus number 2
<6>[    1.538824] usb20_host usb20_host: irq 49, io mem 0x00000000
<6>[    1.538862] DWC_OTG: Init: Port Power? op_state=1
<6>[    1.538868] DWC_OTG: Init: Power Port (0)
<6>[    1.538897] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
<6>[    1.538906] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[    1.538914] usb usb2: Product: DWC OTG Controller
<6>[    1.538920] usb usb2: Manufacturer: Linux 3.0.8+ host20_hcd
<6>[    1.538927] usb usb2: SerialNumber: usb20_host
<6>[    1.539146] hub 2-0:1.0: USB hub found
<6>[    1.539157] hub 2-0:1.0: 1 port detected
<6>[    1.540139] android_usb gadget: Mass Storage Function, version: 2009/09/11
<6>[    1.540149] android_usb gadget: Number of LUNs=2
<6>[    1.540157]  lun0: LUN: removable file: (no medium)
<6>[    1.540164]  lun1: LUN: removable file: (no medium)
<6>[    1.540270] android_usb gadget: android_usb ready
<6>[    1.540427] input: rk29-keypad as /devices/platform/rk29-keypad/input/input0
<4>[    1.540555] __init fts_ts_init
<4>[    1.540737] fts_ts_probe#####################
<4>[    1.540745] file(drivers/input/touchscreen/../../../hena/touchscreen/hena_ft5x0x_i2c_ts.c), function (fts_ts_probe), --probe start
<4>[    1.544849] mma8452 devid:2a
<6>[    1.545195] input: gsensor as /devices/platform/rk30_i2c.0/i2c-0/0-001d/input/input1
<6>[    1.545339] mma8452 probe ok
<6>[    1.545509] using rtc device, tps65910, for alarms
<6>[    1.545708] lirc_dev: IR Remote Control driver registered, major 250
<6>[    1.545717] IR NEC protocol handler initialized
<6>[    1.545722] IR RC5(x) protocol handler initialized
<6>[    1.545728] IR RC6 protocol handler initialized
<6>[    1.545734] IR JVC protocol handler initialized
<6>[    1.545739] IR Sony protocol handler initialized
<6>[    1.545744] IR RC5 (streamzap) protocol handler initialized
<6>[    1.545750] IR LIRC bridge handler initialized
<6>[    1.545755] Linux video capture interface: v2.00
<6>[    1.546128] device-mapper: uevent: version 1.0.3
<6>[    1.546312] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
<6>[    1.546455] Bluetooth: HCI UART driver ver 2.2
<6>[    1.546463] Bluetooth: HCI H4 protocol initialized
<6>[    1.546470] Bluetooth: HCILL protocol initialized
<6>[    1.747162] cpuidle: using governor ladder
<6>[    1.747171] cpuidle: using governor menu
<6>[    1.752410] .Line3891..The End of SDMMC-probe Ver.5.00 The last modify date is 2012-11-05.  [sd_mmc]
<6>[    1.752522] .Line3891..The End of SDMMC-probe Ver.5.00 The last modify date is 2012-11-05.  [sdio]
<7>[    1.752605] Registered led device: button-backlight
<6>[    1.753567] usbcore: registered new interface driver usbhid
<6>[    1.753575] usbhid: USB HID core driver
<6>[    1.755359] logger: created 256K log 'log_main'
<6>[    1.764868]
<6>[    1.764871] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc0]
<6>[    1.769919] rk29_sdmmc_change_clk_div..1928..  newDiv=83, newCLK=298Khz [sd_mmc]
<6>[    1.803382] logger: created 256K log 'log_events'
<6>[    1.808144] logger: created 256K log 'log_radio'
<6>[    1.809092]
<6>[    1.809093] mmc_attach_sd..1218..  ===== Begin to identify card as SD-card. [mmc0]
<6>[    1.821831] logger: created 256K log 'log_system'
<4>[    1.826574] mt6622_probe.
<6>[    1.829198] [MT6622] mt_bt_power_init
<6>[    1.856595] rk29_sdmmc_change_clk_div..1928..  newDiv=0, newCLK=49500Khz [sd_mmc]
<6>[    1.856650] mmc0: new high speed SDHC card at address 1234
<6>[    1.869558] mmcblk0: mmc0:1234 SA08G 7.28 GiB
<6>[    1.875434]
<6>[    1.875436] msdos_partition..461... ==== Begin to parse sdcard-partition.  [mmc0]
<6>[    1.875448] msdos_partition..530... ==== The sdcard has MBR. [mmc0]
<6>[    1.875456] msdos_partition..543... ==== partition-1, size=7638016KB  [mmc0]
<6>[    1.875464] msdos_partition..571... ==== main partition-1....[mmc0]
<6>[    1.875471]  mmcblk0: p1
<6>[    1.875715] mmc_rescan_try_freq..1721..  ===== Initialize SD-card successfully. [mmc0]
<6>[    1.875730]
<6>[    1.875732] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc1]
<4>[    2.105855] firmware version = 0x c
<4>[    2.106262]  firmware report rate = 60Hz
<4>[    2.106659] firmware threshold = 80
<4>[    2.107053]  nosie mode = 0x59
<6>[    2.107656] input: ft5302_ts as /devices/virtual/input/input2
<4>[    2.108089]  function (drivers/input/touchscreen/../../../hena/touchscreen/hena_ft5x0x_i2c_ts.c), -- end
<4>[    2.395060] rk30_adc_battery_load_capacity: open file /data/bat_last_capacity.dat failed
<4>[    3.046845] rt5633_i2c_probe
<6>[    3.253576] asoc: RT5633 HiFi <-> rk29_i2s.0 mapping ok
<6>[    3.253870] ALSA device list:
<6>[    3.253876]   #0: RK29_RT5633
<6>[    3.253944] GACT probability NOT on
<6>[    3.253954] Mirror/redirect action on
<6>[    3.253960] u32 classifier
<6>[    3.253963]     Actions configured
<6>[    3.253969] Netfilter messages via NETLINK v0.30.
<6>[    3.254002] nf_conntrack version 0.5.0 (14199 buckets, 56796 max)
<6>[    3.254305] ctnetlink v0.93: registering with nfnetlink.
<6>[    3.254334] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
<6>[    3.254341] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
<6>[    3.254499] xt_time: kernel timezone is -0000
<6>[    3.254598] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[    3.254700] arp_tables: (C) 2002 David S. Miller
<6>[    3.254736] TCP cubic registered
<6>[    3.255427] NET: Registered protocol family 10
<6>[    3.256221] Mobile IPv6
<6>[    3.256253] ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>[    3.256441] IPv6 over IPv4 tunneling driver
<6>[    3.257187] NET: Registered protocol family 17
<6>[    3.257220] NET: Registered protocol family 15
<5>[    3.257298] Bridge firewalling registered
<6>[    3.264906] Bluetooth: RFCOMM TTY layer initialized
<6>[    3.264929] Bluetooth: RFCOMM socket layer initialized
<6>[    3.264939] Bluetooth: RFCOMM ver 1.11
<6>[    3.264948] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>[    3.264959] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[    3.265072] NET: Registered protocol family 35
<6>[    3.265308] [BT_RFKILL]: Enter rfkill_rk_init
<6>[    3.265374] [BT_RFKILL]: Failed to get bt_default_reset gpio.
<4>[    3.265392] rfkill_rk: probe of rfkill_rk failed with error -1
<6>[    3.265594] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
<4>[    3.266089] rk30-camera version: v0.2.28  Zoom by ipp
<6>[    3.266928] sensor_init: Probe name sensors
<4>[    3.268083] get cif ldo failed!
<6>[    3.273555] tps65910-rtc tps65910-rtc: setting system clock to 2013-09-26 14:18:51 UTC (1380205131)
<6>[    3.273811] Freeing init memory: 756K
<3>[    3.280061] init: /init.rc: 574: invalid option 'start'
<4>[    3.280753] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
<4>[    3.312087] keychord_connect
<6>[    3.312101] keychord: using input dev rk29-keypad for fevent
<3>[    3.312239] init: cannot open '/initlogo.rle'
<4>[    3.374927] get cif ldo failed!
<4>[    3.374937] Probe gc2035_back success
<4>[    3.375014] get cif ldo failed!
<4>[    3.387302] gp_rknand_info = : 0xee8c2200
<4>[    3.387435] request IRQ_NANDC irq , ret=0.........
<4>[    3.387494] FlashCopyProgBuf1=0xc144b000
<4>[    3.387519] ATime: 40 ns AHB: 148 timming: 1081
<4>[    3.387529] No.1 FLASH INFO:2c 64 44 4b a9
<4>[    3.387878] ATime: 32 ns AHB: 148 timming: 1061
<4>[    3.388051] ATime: 32 ns AHB: 148 timming: 1061
<4>[    3.388058] randomizer = 2 , EccBits = 28 pSpec->pReadRetrial = bf00b2f4
<4>[    3.394929] rk30_adc_battery_load_capacity: open file /data/bat_last_capacity.dat failed
<4>[    3.457109] FTL INFO:Version = 438,Date = 20121110
<4>[    3.457117] totalLogicBlkRaw  = 1898
<4>[    3.457131] gBootMedia = 1 gSdmmcFwPartOffset =0!
<4>[    3.457138] rknand_buffer.c version: 4.38 20121110!
<4>[    3.514857] get cif ldo failed!
<4>[    3.514865] Probe gc0308_front success
<5>[    3.514987] 10 cmdlinepart partitions found on MTD device rk29xxnand
<5>[    3.514997] Creating 10 MTD partitions on "rk29xxnand":
<5>[    3.515005] 0x000000400000-0x000000800000 : "misc"
<5>[    3.515635] 0x000000800000-0x000001000000 : "kernel"
<5>[    3.516096] 0x000001000000-0x000002000000 : "boot"
<5>[    3.516509] 0x000002000000-0x000003000000 : "recovery"
<5>[    3.516909] 0x000003000000-0x00001b000000 : "backup"
<5>[    3.517516] 0x00001b000000-0x000023000000 : "cache"
<5>[    3.517991] 0x000023000000-0x0000c3000000 : "userdata"
<5>[    3.519914] 0x0000c3000000-0x0000c3400000 : "kpanic"
<6>[    3.521142] apanic: Bound to mtd partition 'kpanic'
<6>[    3.521149] apanic: No panic data available
<5>[    3.521161] 0x0000c3400000-0x0000eb400000 : "system"
<5>[    3.521940] 0x0000eb400000-0x0001da800000 : "user"
<4>[    3.524599] startBlk = 119  sysProtAddr = 118
<6>[    3.588435] EXT4-fs (mtdblock8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<6>[    3.747224] EXT4-fs (mtdblock6): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<6>[    3.768594] EXT4-fs (mtdblock5): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<4>[    3.771030] UMP: UMP device driver  loaded
<4>[    3.780553] Mali: init_mali_clock mali_clock c0ad1900
<4>[    3.782217] Mali: Mali device driver loaded
<4>[    3.782478] rk29_ipp: module is from the staging directory, the quality is unknown, you have been warned.
<4>[    3.783191] ipp irq 47
<4>[    3.783355] IPP init, version rk30-ipp 1.001
<3>[    3.814915] init: cannot execve('/system/etc/install-recovery.sh'): Permission denied
<4>[    3.850568] vpu: power on
<6>[    3.850627] VPU_SERVICE: HW ID = 0x67312398
<6>[    3.850636] VPU_SERVICE: Compatible HW found at 0x10104400
<6>[    3.850649] VPU_SERVICE: HW ID = 0x48311220
<6>[    3.850657] VPU_SERVICE: Compatible HW found at 0x10104000
<4>[    3.851069] vpu: power off...done
<6>[    3.851099] VPU_SERVICE: init success
<6>[    3.956336] rk_serial rk_serial.0: serial_rk_init_dma_rx sucess
<3>[    3.956599] init: using deprecated syntax for specifying property 'ro.product.usbfactory', use ${name} instead
<3>[    3.958004] android_usb: already disabled
<6>[    3.962717] adb_open
<6>[    4.690408] .409.. MMC0 receive the message sd-No-Media from VOLD.[sd_mmc]
<6>[    4.690424] .440.. MMC0 receive the message No-Media from VOLD. waitTimes=0 [sd_mmc]
<6>[    5.194565] .409.. MMC0 receive the message sd-Pending from VOLD.[sd_mmc]
<4>[    5.513913] Current WiFi chip is MT5931.
<3>[    6.675683] gc2035 sensor_ioctl cmd(0x3) is unknown !
<3>[    6.784939] gc0308 sensor_ioctl cmd(0x3) is unknown !
<4>[    7.394990] rk fb use 3 buffers
<4>[    7.854845] delayed
<6>[    9.554858] DWC_OTG: dwc_otg_hcd_connect_detect schedule delaywork
<6>[    9.634890] DWC_OTG: dwc_otg_hcd_enable, disable host controller
<6>[    9.634909] DWC_OTG: PortPower off
<6>[   10.194901] .409.. MMC0 receive the message sd-Idle-Unmounted from VOLD.[sd_mmc]
<6>[   10.195237] .409.. MMC0 receive the message sd-Checking from VOLD.[sd_mmc]
<6>[   10.200214] .409.. MMC0 receive the message sd-Mounted from VOLD.[sd_mmc]
<6>[   11.544946] warning: `zygote' uses 32-bit capabilities (legacy support in use)
<3>[   11.815626] init: sys_prop: permission denied uid:1003  name:service.bootanim.exit
<4>[   15.582691] Current WiFi chip is MT5931.
<4>[   15.589063] =======================================================
<4>[   15.589082] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
<4>[   15.589092] =======================================================
<4>[   15.589101] initRssiHistory.
<4>[   15.589110] MT5931 SDIO WiFi driver (Powered by Rockchip,Ver 2.10) init.
<4>[   15.589119] initWlan
<4>[   15.589124] ## Calling platform_driver_register
<4>[   15.589188] ## wifi_probe
<4>[   15.589197] wifi_set_power = 1
<6>[   15.589204] rk29sdk_wifi_power: 1
<6>[   15.683776] acc_open
<6>[   15.685987] acc_release
<6>[   15.949702] wifi turn on power
<4>[   15.949716] wifi_set_carddetect = 1
<6>[   15.949722] rk29sdk_wifi_set_carddetect:1
<6>[   15.949731] mmc1: slot status change detected(0-1)
<6>[   15.949778] rk29_sdmmc_change_clk_div..1928..  newDiv=42, newCLK=294Khz [sdio]
<4>[   15.975681] wl_android_wifictrl_func_add success.
<6>[   16.144933]
<6>[   16.144935] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc1]
<6>[   16.188909]
<6>[   16.188911] mmc_attach_sdio..800..  ===== Begin to identify card as SDIO-card. [mmc1]
<6>[   16.221981] rk29_sdmmc_change_clk_div..1928..  newDiv=0, newCLK=24750Khz [sdio]
<6>[   16.222838] mmc1: new high speed SDIO card at address 0001
<4>[   16.223209] wireless_dev prWdev(0xedf92000) allocated
<4>[   16.223227] wiphy (0xed4ea120) allocated
<4>[   16.223245] net_device prDev(0xed646800) allocated
<4>[   16.224572] Open FW image: WIFI_RAM_CODE failed
<4>[   16.224581] Remove wlan!
<4>[   16.224585] 0 == u4WlanDevNum
<4>[   16.224599] wlan: probe of mmc1:0001:1 failed with error -1
<6>[   16.224613] mmc_rescan_try_freq..1678..  ===== Initialize SDIO successfully. [mmc1]
<3>[   35.515292] elevator: type
<3>[   35.515295]  not found
<3>[   35.515308] elevator: switch to
<3>[   35.515310]  failed
<3>[   36.440702] init: untracked pid 1149 exited
<3>[   36.664726] init: untracked pid 1174 exited
<3>[   43.047953] init: untracked pid 1380 exited
<4>[  121.450753] =======================================================
<4>[  121.450809] == Dis-launching Wi-Fi driver! (Powered by Rockchip) ==
<4>[  121.450848] =======================================================
<4>[  121.450884] Remove wlan!
<4>[  121.450905] 0 == u4WlanDevNum
<4>[  121.452676] ## Unregister platform_driver_register
<4>[  121.452773] ## wifi_remove
<4>[  121.452801] wifi_set_power = 0
<6>[  121.452830] rk29sdk_wifi_power: 0
<6>[  121.659966] wifi shut off power
<4>[  121.659980] wifi_set_carddetect = 0
<6>[  121.659986] rk29sdk_wifi_set_carddetect:0
<6>[  121.659994] mmc1: slot status change detected(1-0)
<6>[  121.660115] mmc1: card 0001 removed
<6>[  121.660165]
<6>[  121.660167] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc1]
<4>[  121.663432] exitWlan
<5>[  320.434532] CPU1: shutdown
<6>[  320.441589] request_suspend_state: sleep (3->3) at 320446724708 (2013-09-26 14:24:08.659178414 UTC)
<6>[  320.451453] rk30-hdmi rk30-hdmi: Removed.
<4>[  320.455966] drivers/video/backlight/../../../hena/backlight/hena_backlight_demo.c : rk29_bl_suspend
<4>[  320.501109] enter ft5x0x_ts_early_suspend
<6>[  571.956566] request_suspend_state: wakeup (3->0) at 571961699655 (2013-09-26 14:28:20.174153944 UTC)
<4>[  571.966080] ft5x0x_ts_late_resume finish
<4>[  572.015376] CPU1: Booted secondary processor
<6>[  572.024862] Switched to NOHz mode on CPU #1
<4>[  572.618622] Current WiFi chip is MT5931.
<4>[  572.624360] =======================================================
<4>[  572.636330] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
<4>[  572.649740] =======================================================
<4>[  572.656174] initRssiHistory.
<4>[  572.656183] MT5931 SDIO WiFi driver (Powered by Rockchip,Ver 2.10) init.
<4>[  572.656187] initWlan
<4>[  572.656190] ## Calling platform_driver_register
<4>[  572.656256] ## wifi_probe
<4>[  572.656260] wifi_set_power = 1
<6>[  572.656264] rk29sdk_wifi_power: 1
<6>[  572.946786] wifi turn on power
<4>[  572.949968] wifi_set_carddetect = 1
<6>[  572.953473] rk29sdk_wifi_set_carddetect:1
<6>[  572.953481] mmc1: slot status change detected(0-1)
<6>[  572.953529] rk29_sdmmc_change_clk_div..1928..  newDiv=42, newCLK=294Khz [sdio]
<4>[  572.954468] wl_android_wifictrl_func_add success.
<6>[  573.144911]
<6>[  573.144914] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc1]
<6>[  573.188891]
<6>[  573.188894] mmc_attach_sdio..800..  ===== Begin to identify card as SDIO-card. [mmc1]
<6>[  573.224286] rk29_sdmmc_change_clk_div..1928..  newDiv=0, newCLK=24750Khz [sdio]
<6>[  573.225078] mmc1: new high speed SDIO card at address 0001
<4>[  573.225494] wireless_dev prWdev(0xe6e04e00) allocated
<4>[  573.225512] wiphy (0xe76da120) allocated
<4>[  573.225530] net_device prDev(0xed647800) allocated
<4>[  573.225727] Open FW image: WIFI_RAM_CODE failed
<4>[  573.225734] Remove wlan!
<4>[  573.225738] 0 == u4WlanDevNum
<4>[  573.225750] wlan: probe of mmc1:0001:1 failed with error -1
<6>[  573.225761] mmc_rescan_try_freq..1678..  ===== Initialize SDIO successfully. [mmc1]
<3>[  677.641374] wlan: version magic '3.0.36+ SMP preempt mod_unload ARMv7 ' should be '3.0.8+ SMP preempt mod_unload ARMv7 '
<4>[  688.350258] =======================================================
<4>[  688.350278] == Dis-launching Wi-Fi driver! (Powered by Rockchip) ==
<4>[  688.350290] =======================================================
<4>[  688.350302] Remove wlan!
<4>[  688.350309] 0 == u4WlanDevNum
<4>[  688.350504] ## Unregister platform_driver_register
<4>[  688.350537] ## wifi_remove
<4>[  688.350546] wifi_set_power = 0
<6>[  688.350556] rk29sdk_wifi_power: 0
<6>[  688.558936] wifi shut off power
<4>[  688.562089] wifi_set_carddetect = 0
<6>[  688.564862] rk29sdk_wifi_set_carddetect:0
<6>[  688.564872] mmc1: slot status change detected(1-0)
<6>[  688.565876] mmc1: card 0001 removed
<6>[  688.578273]
<6>[  688.578275] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc1]
<4>[  688.579068] exitWlan
<5>[  764.444836] CPU1: shutdown
<6>[  764.449894] request_suspend_state: sleep (0->3) at 764455031844 (2013-09-26 14:31:32.667486050 UTC)
<6>[  764.459752] rk30-hdmi rk30-hdmi: Removed.
<4>[  764.463870] drivers/video/backlight/../../../hena/backlight/hena_backlight_demo.c : rk29_bl_suspend
<4>[  764.514954] enter ft5x0x_ts_early_suspend
<6>[  768.907201] request_suspend_state: wakeup (3->0) at 768912335178 (2013-09-26 14:31:37.124789217 UTC)
<4>[  768.916483] ft5x0x_ts_late_resume finish
<4>[  768.965375] CPU1: Booted secondary processor
<6>[  768.974845] Switched to NOHz mode on CPU #1
<4>[  769.504040] Current WiFi chip is MT5931.
<4>[  769.505084] =======================================================
<4>[  769.505101] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
<4>[  769.505113] =======================================================
<4>[  769.505124] initRssiHistory.
<4>[  769.505134] MT5931 SDIO WiFi driver (Powered by Rockchip,Ver 2.10) init.
<4>[  769.505145] initWlan
<4>[  769.505152] ## Calling platform_driver_register
<4>[  769.505228] ## wifi_probe
<4>[  769.505239] wifi_set_power = 1
<6>[  769.505248] rk29sdk_wifi_power: 1
<6>[  769.774702] wifi turn on power
<4>[  769.774715] wifi_set_carddetect = 1
<6>[  769.774722] rk29sdk_wifi_set_carddetect:1
<6>[  769.774730] mmc1: slot status change detected(0-1)
<6>[  769.774774] rk29_sdmmc_change_clk_div..1928..  newDiv=42, newCLK=294Khz [sdio]
<4>[  769.775391] wl_android_wifictrl_func_add success.
<6>[  769.964855]
<6>[  769.964857] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc1]
<6>[  770.008731]
<6>[  770.008733] mmc_attach_sdio..800..  ===== Begin to identify card as SDIO-card. [mmc1]
<6>[  770.040121] rk29_sdmmc_change_clk_div..1928..  newDiv=0, newCLK=24750Khz [sdio]
<6>[  770.048120] mmc1: new high speed SDIO card at address 0001
<4>[  770.054445] wireless_dev prWdev(0xdf87a600) allocated
<4>[  770.059519] wiphy (0xe76d8120) allocated
<4>[  770.063455] net_device prDev(0xed644000) allocated
<4>[  770.068444] Open FW image: WIFI_RAM_CODE failed
<4>[  770.073008] Remove wlan!
<4>[  770.074874] 0 == u4WlanDevNum
<4>[  770.074895] wlan: probe of mmc1:0001:1 failed with error -1
<6>[  770.074909] mmc_rescan_try_freq..1678..  ===== Initialize SDIO successfully. [mmc1]
<5>[  835.774770] CPU1: shutdown
<6>[  835.798442] request_suspend_state: sleep (0->3) at 835803579935 (2013-09-26 14:32:44.016032974 UTC)
<6>[  835.808252] rk30-hdmi rk30-hdmi: Removed.
<4>[  835.812290] drivers/video/backlight/../../../hena/backlight/hena_backlight_demo.c : rk29_bl_suspend
<4>[  835.866388] enter ft5x0x_ts_early_suspend
<6>[  839.008377] request_suspend_state: wakeup (3->0) at 839013510728 (2013-09-26 14:32:47.225964976 UTC)
<4>[  839.017673] ft5x0x_ts_late_resume finish
<4>[  839.065551] CPU1: Booted secondary processor
<6>[  839.074846] Switched to NOHz mode on CPU #1
<4>[  844.976950] =======================================================
<4>[  844.977008] == Dis-launching Wi-Fi driver! (Powered by Rockchip) ==
<4>[  844.977046] =======================================================
<4>[  844.977081] Remove wlan!
<4>[  844.977103] 0 == u4WlanDevNum
<4>[  844.978505] ## Unregister platform_driver_register
<4>[  844.978601] ## wifi_remove
<4>[  844.978629] wifi_set_power = 0
<6>[  844.978658] rk29sdk_wifi_power: 0
<6>[  845.180845] wifi shut off power
<4>[  845.180858] wifi_set_carddetect = 0
<6>[  845.180864] rk29sdk_wifi_set_carddetect:0
<6>[  845.180871] mmc1: slot status change detected(1-0)
<4>[  845.181511] exitWlan
<6>[  845.198486] mmc1: card 0001 removed
<6>[  845.202052]
<6>[  845.202054] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc1]
<5>[  899.064591] CPU1: shutdown
<6>[  899.069401] request_suspend_state: sleep (0->3) at 899074540193 (2013-09-26 14:33:47.286993982 UTC)
<6>[  899.080262] rk30-hdmi rk30-hdmi: Removed.
<4>[  899.084518] drivers/video/backlight/../../../hena/backlight/hena_backlight_demo.c : rk29_bl_suspend
<4>[  899.130739] enter ft5x0x_ts_early_suspend
<6>[  900.797163] request_suspend_state: wakeup (3->0) at 900802295985 (2013-09-26 14:33:49.014750025 UTC)
<4>[  900.806446] ft5x0x_ts_late_resume finish
<4>[  900.856014] CPU1: Booted secondary processor
<6>[  900.864845] Switched to NOHz mode on CPU #1
<4>[  901.416261] Current WiFi chip is MT5931.
<4>[  901.418467] =======================================================
<4>[  901.418484] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
<4>[  901.418495] =======================================================
<4>[  901.418507] initRssiHistory.
<4>[  901.418518] MT5931 SDIO WiFi driver (Powered by Rockchip,Ver 2.10) init.
<4>[  901.418529] initWlan
<4>[  901.418535] ## Calling platform_driver_register
<4>[  901.418608] ## wifi_probe
<4>[  901.418619] wifi_set_power = 1
<6>[  901.418628] rk29sdk_wifi_power: 1
<6>[  901.680725] wifi turn on power
<4>[  901.680738] wifi_set_carddetect = 1
<6>[  901.680745] rk29sdk_wifi_set_carddetect:1
<6>[  901.680752] mmc1: slot status change detected(0-1)
<6>[  901.680794] rk29_sdmmc_change_clk_div..1928..  newDiv=42, newCLK=294Khz [sdio]
<4>[  901.681397] wl_android_wifictrl_func_add success.
<6>[  901.874850]
<6>[  901.874852] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc1]
<6>[  901.918723]
<6>[  901.918725] mmc_attach_sdio..800..  ===== Begin to identify card as SDIO-card. [mmc1]
<6>[  901.953289] rk29_sdmmc_change_clk_div..1928..  newDiv=0, newCLK=24750Khz [sdio]
<6>[  901.961287] mmc1: new high speed SDIO card at address 0001
<4>[  901.965636] wireless_dev prWdev(0xe3021a00) allocated
<4>[  901.965656] wiphy (0xc22de120) allocated
<4>[  901.965674] net_device prDev(0xed98f000) allocated
<4>[  901.965860] Open FW image: WIFI_RAM_CODE failed
<4>[  901.965867] Remove wlan!
<4>[  901.965872] 0 == u4WlanDevNum
<4>[  901.965884] wlan: probe of mmc1:0001:1 failed with error -1
<6>[  901.965897] mmc_rescan_try_freq..1678..  ===== Initialize SDIO successfully. [mmc1]
<4>[  906.894540] =======================================================
<4>[  906.904963] == Dis-launching Wi-Fi driver! (Powered by Rockchip) ==
<4>[  906.905009] =======================================================
<4>[  906.905046] Remove wlan!
<4>[  906.905068] 0 == u4WlanDevNum
<4>[  906.906516] ## Unregister platform_driver_register
<4>[  906.906608] ## wifi_remove
<4>[  906.906638] wifi_set_power = 0
<6>[  906.906666] rk29sdk_wifi_power: 0
<6>[  907.109811] wifi shut off power
<4>[  907.109825] wifi_set_carddetect = 0
<6>[  907.109831] rk29sdk_wifi_set_carddetect:0
<6>[  907.109839] mmc1: slot status change detected(1-0)
<4>[  907.110497] exitWlan
<6>[  907.111302] mmc1: card 0001 removed
<6>[  907.111353]
<6>[  907.111355] drivers/mmc/core/core.c...1827..  ===== mmc_rescan Begin....[mmc1]